The purpose of this study was to gather knowledge about the functioning of the Rein tension meter and test it for future studies of match and mismatch between rider and horse. We looked specifically into the possibilities to use a rein-tension meter to determine the quality of cooperation between horse and rider. We examined whether a rider shows a specific tension pattern and also if certain patterns could be recognised for a specific horse. During the study, a manual with pictures and text was written to support the practical use of the meter. The manual describes in a simple way the first steps in the installation and use of the meter.

A large part of the interactions between horse and rider during horseback riding takes place through the reins and the bit and devices for measuring the tension on the reins, Rein tension meters, has fairly recently been developed. To safeguard the welfare of the ridden horse riders need to be aware of the Rein tension they apply and actively work to decrease it. Furthermore, there is a need to develop the study of Rein tension through new techniques and refined analysis procedures. A good-quality Rein tension meter should be small in size, sensitive, durable and as accurate for light Rein tension as for strong forces. Rein tension meters used in research on horse and rider interaction commonly depend on strain gauge technique for generating Rein tension data.

One way of signalling commands to the horse during riding is through applying tension on the reins to create bit pressure in the horse?s mouth (Terada et al., 2006; Clayton et al., 2011). The skilfulness of the rider in using the hands when applying bit pressure has consequences both for the horse?s performance and welfare (Manfredi et al., 2010). At the trot there are large vertical deviations of the horse?s body which the rider must adjust and adapt to (Terada et al., 2006) and an unsteady hand due to inability to follow the horse?s movement can be a source of discomfort and conflict behaviour in the horse (Heleski et al., 2009).

This essay derives from the concern that horses ridden with a bit in their mouth can be subjected to strong pressure from the bit if the horse and rider do not understand each other. The horse's mucosa membrane and the tongue are very sensitive tissues (Cook, 1999; Manfredi, 2005; Oliveira, 2005; Terada, 2006) and the bit can then be a source of pain and discomfort. The training of the horse should therefore always be a step by step process and as the horse develops difficulties are increased. Oliveira (2005) suggested that high demands can be placed on the horse but to be successful in the training it is essential to be content with small progress and reward the slightest desired response from the horse. This corresponds with the principles of operant conditioning with negative reinforcement.

Superficial digital flexor tendon injuries are common causes of premature retirement or pre-longed convalescence periods for race horses. The curve gradient at Täby Galopp race track is very small and most races as well as high speed training are done on the left rein. It is believed that the horses left foreleg is under considerably more strain then the right foreleg when being ridden on the left rein during gallop at high speed. During gallop on the left rein the horse puts its entire weight on the left foreleg when regaining ground contact. The purpose of this study has been to find out, through analyzing the statistics concerning the horses that visited the ATG clinic at Täby during a period between January 2003 and September 2006, whether there is a higher frequency of superficial digital flexor tendon injuries on the left leg rather than the right and if so, can this support the theory that the design of the race track in combination with continuous left rein races can be a contributing cause of these injuries. The result of the study shows that 57% of the tendon injuries occurred on the left front leg and 38% on the right front leg. The difference is not large enough to support the above theory of the underlying cause of these injuries..

Title: Alexander Technique - Different thoughts on the Alexander Technique and its effect on the singing voice. Does singing lessons cause tension in the student? What should you as a teacher consider to avoid situations that cause tension? This examination is based on interviews. The persons who have been interviewed are singing students, singing teachers and teachers in the Alexander Technique. The literature and the interviews describe the Alexander Technique as a method that, with support of a teacher of the Alexander Technique, helps you to recreate the balance between the cranium, neck and spine.

In this study, the pre-tension force in an insert screw connection are examined in order to establish a greater understanding of the system and to facilitate the process of making new metal cutting tools. Certain especially significant design variables such as the offset, the length of the contact thread and the shank length above the threaded hole, are selected to be closely examined. A comparison of the influence on the pre-tension force between threaded holes made with a worn, versus new, threading tool is also involved in the experiment. The study is limited to handling the screw sizes M2,5 and M3,5. The results show that a regression model, with good approximation, can be fitted to the measured values.

The purpose with this thesis was to examine the cold rolling mill located at Högskolan Dalarna and to stabilize the rolling process, to achieve steady state. Experiments with cold rolling of an aluminium strip have given results for rolling force, friction, reduction, strip tension and strain hardening. Results show that steady state has been found for the experiments with roll force and strain hardening, and not been found for the experiments with friction and reduction. Results show that increased strip tension gives lower roll forces. The roll force equation of Stone shows comparable results with reality for dry contact with reductions up to 30 %, but starts being incomparable with higher reductions.

This thesis was performed at Vendig AB which is a company that develops and sells products such as belt scrapers for conveyor. The thesis is divided into two parts, one part where it´s investigated which tension force is required to tighten Vendig AB´s scraper Hampus against the belt in a correct way. The second part is called mechanical design and here a new and more compact tension device is developed.Field studies has been conducted at a couple of Vendig AB´s costumers to get a knowledge base about how Vendig AB´s products are used, how they function and the environment they operate in. During one of the field studies the force between the scraper and the belt was measured. The result from the measurements, together with a report from LKAB [1], were evaluated and summarized in a table.

This report presents an independent thesis corresponding 15hp and was carried out on Högskolan in Halmstad during the spring of 2014. The thesis is the final course which ends a three-year mechanical engineering program with focus on technical design.The thesis started in an operation which electricians are exposed to every day. The operation in question is cable laying or wiring. The tool they use is called a tension spring and is a long and stiff wire, usually made out of nylon or fiberglass. The tension spring is fed through pipes in the walls and brings the desired cables with it on the way back.

The drama of Kristina Lugn?s Kvinnorna vid Svansjön (The women by the Swan Lake) takes place in the dialogue and language; the same ambiguous language that is found in Lugn?s poetry. In this essay I examine how meaning and dramatic tension is created in the dialogue of Kvinnorna vid Svansjön.I describe the play, using concepts from various drama theories. However, the most important concepts of classical drama theory such as "story" and "plot" are not really applicable. This is because of the contradictory information given in the dialogue.

The city?s public environments are meant to be perceived as safe and inviting areas to visit any time of the day. In recent decades the number of vandalism complaints has doubled and graffiti has become so common that it received a separate category in the crime statistics. With this type of impacts in the public environments the experience are precarious and a boring sight. It?s difficult to put a price tag on these types of crimes, the number of unreported cases suspected to be large.

The underlying purpose of this study is to investigate how the libraries in Sweden organize and administrate the service of providing literature in other languages than Swedish. The study focuses on the central guiding principles that regulate the provision of multilingual literature and how these guidelines are implemented in to practice at the libraries. As the guidelines are closely connected to the official discourse in Sweden concerning policies targeted towards immigrants, the guidelines will be examined from a perspective of integration politics. To assemble data a survey has been conducted looking into factors such as how the libraries perceive the guidelines, how the libraries do business intelligence and user inquires to reach out to the users of the multilingual media, forms for statistics and method of working. The results points out that the libraries in their work with multilingual media are confronted with three tensions; the first tension is that between the libraries aim to promote equality and freedom for the individual and at the same time to fulfil certain collective interests and goals.

This report reflects an examination work performed for Getrag All Wheel Drive AB during the spring of 2005. Among the companies range of products there exists some concern regarding the amount of clamping force and friction on bolted joints caused by the assembly torque.The aim of this project has been to determine if there is a simple way in which to identify and then practically apply testing methods for clamping force and friction through utilization of existing testing equipment.Three separate methods of clamping force and friction determination have been tested in rear drive unit, RDU, at a 30 Nm assembly torque. A fourth and final method, screw elongation with ultrasound, has been used as reference. The methods are:?Torque-Tension test.?Screw elongation with micrometer.?Joint stiffness test.?Screw elongation with ultra sound for reference.The results from tests can be viewed in table below.MethodTorque-TensionMicrometerCs=318 kN/mm Assembled with torque wrenchMicrometerCs=318 kN/mm Assembled on lineUltra-soundCS=311 kN/mm Ultra- soundCS=318 kN/mm Joint stiffnessTheoreticalClamping force-21,8 kN17,6 kN17,3 kN17,6 kN17,1 kN17,3 kNFriction-0,110,1470,1530,1470,1520,149.

AimThe aim with this study was to acquire knowledge of mental training and if you can use it in the elementary school to increase in a short period of time the performance in a coordination test. Furthermore we wanted to investigate teachers understanding of the possibilities to perform this kind of training in the elementary school, and if there is support for this in the school regulation.MethodAs method we have used a combination of a literature pre-study, interview and at the end an experiment. Before the experiment and interviews could take place we studied literature about mental training to get a basic knowledge of the subject. The facts we learned from our pre-study and interviews gave us the base for our experiment. The experiment group included 23 pupils in a third class at school situated in Stockholm.